Search results

The purpose of this study is to explore the mechanism of branch pits and tunnels formation and increase the specific surface area and capacitance of anode Al foil for high voltage electrolytic capacitor by D.C. etching in acidic solution and neutral.

Al foil was first D.C. etched in HCl-H₂SO₄ mixed acidic solution to form main tunnels perpendicular to the Al surface, and then D.C. etched in neutral NaCl solution including 0.5 per cent C₆H₈O₇ and Cu(NO₃)₂ with different concentration to form branch tunnels normal to Al surface. Between two etching, Cu nuclei were electroless deposited on the interior surface of main tunnels by natural occluded corrosion cell effect to form micro Cu-Al galvanic local cells. The effects of electroless deposited Cu nuclei on cross-section etching morphologies and electrochemical behavior of Al foil was investigated with SEM, polarization curve and electrochemical impedance spectroscopy (EIS).

The results show that sub branch tunnels can form along the main tunnels owing to the formation of Cu-Al micro-batteries, in which Cu is cathode and Al is anode. With increase in Cu(NO₃)₂ concentration, more Cu nuclei can be electroless deposited and serve as the favorable sites for branch tunnel initiation along the whole length of main tunnels, leading to enhancement in specific capacitance of anode Al foil.

Cu nuclei were electroless deposited on the interior surface of main tunnels by natural occluded corrosion cell effect to form micro Cu-Al galvanic local cells, which can serve as the favorable sites for branch tunnel initiation along the main tunnels to enhance specific capacitance of anode Al foil.

The purpose of this paper is to find out the anti‐smoking counselling frequency and its correlates in a sample of Chinese physicians.

In this paper, 268 physicians in Baoding, a city near Beijing, filled out a questionnaire asking about their own smoking status, their anti‐smoking behaviors as well as their opinions on how to reduce cigarette smoking in China.

The paper finds that 54 percent of the male and 8.4 percent of the female physicians were current cigarette smokers. When asked whether they had counselled their patients about cigarette smoking in the past year, 43.7 percent answered “always”; 38.1 percent “often”; 13.1 percent “sometimes”; 2.6 percent “occasionally”, and 2.6 percent said: “not much”. However, only 9.0 percent said that they were “very successful”. Physicians' anti‐smoking counselling practices were highly correlated with their own smoking status; whether they perceived their past anti‐smoking activities as successful; whether they thought that they should set examples by not smoking; whether they felt that they had the responsibility to help patients and whether they perceived themselves as influential in persuading patients to quit smoking.

The paper shows that messages aimed at increasing Chinese physicians' anti‐smoking counselling should appeal to their responsibility, exemplary role, and unique influence on patients' health‐related behaviors.

The paper adds to the few studies on Chinese physicians' cigarette smoking behavior and their anti‐smoking activities. In a country where cigarette smoking is a way of life among males, and few people are aware of the health consequences of cigarette smoking, physicians' efforts can be a spearhead to a cessation campaign.

This paper aims to design a new full‐body tactile sensor which is essential for the application of personal service robot similar to human skin.

The largest difficulty for designing a full‐body tactile sensor is the huge number of output connections. The sensor introduced in this paper is a special multi‐layer structure, which could minimize the output connections while sensing both the position and force information. Since it is made of conductive and non‐conductive textiles, the sensor could be used to cover the curved surface of robot body.

With better structure design, output connectors and signal measurement times could be dramatically reduced.

Sensor area and performance are limited by the sensitivity of the measurement circuits.

Introduces an innovate design of full‐body tactile sensor.

The purpose of this paper is to give a comprehensive survey on the physics-based virtual assembly (PBVA) technology in a novel perspective, to analyze current drawbacks and propose several promising future directions.

To provide a deep insight of PBVA, a discussion of the developing context of PBVA and a comparison against constraint-based virtual assembly (CBVA) is put forward. The core elements and general structure are analyzed based on typical PBVA systems. Some common key issues as well as common drawbacks are discussed, based on which the research trend and several promising future directions are proposed.

Special attention is paid to new research progresses and new ideas concerning recent development as well as new typical systems of the technology. Advantages of PBVA over CBVA are investigated. Based on the analysis of typical PBVA systems and the evolution of PBVA, the core elements of the technology and the general structure of its implementation are identified. Then, current PBVA systems are summarized and classified. After that, key issues in the technology and current drawbacks are explored in detail. Finally, promising future directions are given, including both the further perfecting of the technology and the combination with other technologies.

The PBVA technology is put into a detailed review and analysis in a novel way, providing a better insight of both the theory and the implementation of the technology.